Thanks to current digital technology, multi-track live recordings are anything but rocket science today.
Howdy SEA Fans, Welcome to another tiptuesday blog post and today we are discussing some tips which will be quintessential for those FOH Engineers who want to perfectly record a live band performance.
Regardless of whether it is a self-sufficient HD recorder or a compact notebook with a powerful audio interface: 16 or even 24 tracks can be captured on the hard disk or flash memory without any fuss.
This is particularly easy with digital mixing consoles that stream their channel strips directly into the computer via USB, but also the playback of the recording signals via an analog console is quickly done.
The following 4 tips should help you to bring FOH and recording as stress-free as possible on the stage.
Don’t try to experiment with new Gadgets
Only use equipment that you know well for the recording session.
Nothing is more annoying than a messed up recording, because in the heat of the moment something has been messed up.
That sounds trivial, but when the recording is added to the FOH job, the stress level increases.
Preparation is a must.
Careful installation of the backline and microphones helps to limit later crosstalk in advance.
Record at least two songs and make sure that no clipping occurs.
No matter whether you record with a notebook or a 19-inch recorder: Document before the gig, on which lane which signal lies.
Record the Atmosphere
Set up microphones for the hall atmosphere.
Favorable positions are at the edge of the stage and / or at the FOH-Platz.
However, FOH should not stand 20 meters away from the stage.
Unsuitable for Atmos microphones are places where the audience can cough directly into the microphones or kick their tripods.
Better in front of the fader
Ideally, the signals for the multi-track recorder are picked up by a send path from the FOH console.
This should be pre-fader, because the recording level remains constant, even if you have to adjust for the hall during the concert.
If your console does not have a free pre-fader aux, you can work with a post-fader send if necessary.
However, this may make the later mixing more difficult.
Alternatively, you can use a separate recording mixer.
Hope you have found the above-mentioned tips useful.
Do share you perspective about the tips shared above as a comment below.
In India, most of the of events are happening indoors, and the concrete multipurpose hall is actually a nightmare for the sound engineer.
It is an undeniable fact that many of these concrete bunkers have such modest acoustics, which is actually disgusting for the sound engineering technician and a factor that takes away the fun of working.
While it scares us, the audience expects – quite rightly – a transparent, professional sound.
What to do?
Howdy SEA Fans, Welcome to another tiptuesday blog post and the topic we are discussing today will be beneficial for those who sound engineers who are doing sound setup in ca onfined atmosphere and here are some practical tips to avert the sonic disaster.
What is bad acoustics?
There are several parameters that can be used to capture the acoustics of a room.
Among the best known are the cryptic abbreviations RT60 and STI.
This is often the money because cost-effective construction and dry room acoustics are difficult to reconcile.
While talking one of the acoustic consultant and sound engineer here in kerala, he told that there are many big halls and sacred buildings in the state, which are not acoustic friendly and those who are gathering inside the building are not able to hear it properly.
Those who are constructing the building will be spending a huge amount for erecting the building and decorating it and a marginal amount is being spent for sound installation and acoustics and that will reflect in the overall sound output.
The reason is that most of the builders are not taking care of the acoustics part while construction. Even if the building construction is acoustically perfect the sound will not be audible if the audio setup is imperfect as room acoustics was not taken into consideration while setting up.
Buildings made of concrete and glass, in which walls and ceilings are at right angles to each other, can be erected quickly and cost-effectively.
The fact that you create spaces that have virtually no sound-absorbing surfaces and throw sound back directly into the room, the task of the sound engineer hardly facilitates.
1. Room Acoustics
Too much reverberation sounds awful, everyone knows that.
Our goal is, therefore, to prevent as many direct reflections as possible.
You have to distinguish reflections by PA and stage.
Our work starts on stage because reflections make it hard for the musicians to hear each other clearly.
This, in turn, leads the musicians to turn their amps louder, to play louder and as a consequence demand a louder monitor sound.
So the FoH technician gives more steam to the monitors and at the same time more levels to the PA.
The result is an unnecessarily loud FoH sound that creates further reflections.
There are actors who, after many years in front of the camera, also want to prove themselves at the theater. The job is the same, but the conditions sometimes completely different. While you can easily repeat a failed take in front of the camera, a hang-up in the theater is a real showstopper in the worst case scenario. The same applies to the sound engineering.
Howdy SEA Fans, Welcome to another tiptuesday blog post and the topic we are discussing today will be beneficial for those studio sound engineers who are planning to do the live mixing or to become a FOH Engineer. Last week we have published an article which discussed tips on starting a career in game sound design and hope you have found it interesting as well.
Let’s continue with today’s topic,.
There are colleagues who turn the knobs exclusively in the recording studio and one day receive the offer to supervise a band not only in the studio but also at concerts on the podium.
An adventure that does not necessarily have to be profitable for both parties.
Sure, the studio sound engineer knows the sounds of the band very well and also knows which microphones and effects he has used for specific sound.
But is that enough on a live construction site to guarantee a good sound?
Here are those tips for studio sound engineers who dare to go live for the first time.
Work with the room acoustics
“The first time you will not forget”, which also applies to the studio technician who will mix for the first time a band in a concrete (modern multi-purpose hall).
“Has the reverb unit not been muted?”, Some studio co-workers may have asked themselves during the soundcheck.
In the studio, you work in acoustically optimized rooms.
Dry acoustics, a smooth decay of frequencies, absorption and diffusion make listening and precise mixing comparatively easy. At least, it’s much easier than amplifying a band over a PA in an acoustically difficult room.
You can not interfere with poor room acoustics.
You can only try to live with it.
Say: If the hall is particularly “reverberant”, then the reverbs stay off.
What good is it if the vocal hall settings of the last studio production only make the singing at the concert even more incomprehensible?
Mix in multitask mode
In the studio, the sound engineer usually only looks after a mix.
Either the headphone mix of the musician or you mix the overall result.
If the band plays live, many professional studios have their own mix systems for the musicians.
This is also legitimate because as a studio sound engineer you should always have the main focus on the performance and quality of the signals being recorded.
The live world is often different. If the monitor mix from the FoH, so you have to familiarize yourself with the idea that in addition to the front mix still some monitor mix for the musicians.
All these mixes are important and have a direct influence on the success of a concert.
How do experienced live sound engineers recognize a studio colleague? If after fifteen minutes soundcheck is still screwed to the bass drum sound.
In Live there are no hours of trying out.
One should put the perfectionism out of the studio and fast. Otherwise, festival gigs could mutate into a nightmare experience with a 15-minute break.
The right volume
Incidentally, this point also applies to amateur sound engineers who are allowed to mix a big show on a fat system for the first time.
The fact is: you do not have to operate every PA at the limit.
Large systems are therefore generously dimensioned to provide comfortable headroom for sporadic peaks.
Without experience, it is difficult to properly estimate the volume of a large PA system.
Especially since professional systems have no problem with low-distortion and low-distortion reproduction at high levels.
As a studio technician is, however, the current massively compressed “In your face Sound” from the studio used and it is close to wanting to convey this listening experience on the volume.
Just look at the SPL meter now and then.
Caution with the duo “Compressor & Limiter”
The sound of modern rock and pop music is strongly influenced by the massive use of Dynamic Limiters, Compressors, Saturators, Clippers, etc.
Live can be the same mix technique but powerful backfire. Too much compression and limiting can make a mix seem ridiculous and lifeless.
The deliberate distortion of signal sources can in the worst case even end in a feedback inferno.
But the crassly distorted vocals give the song a fat extra boost?
Then it’s better to record these distorted vocals as backing tracks than to make them live with a distortion effect.
Distorted signals have a low dynamic range and are therefore particularly suitable for stage monitors without great premonitions
Hope you have found the tips which we have discussed in this post on the things to consider while a studio engineer transforms himself to a FOH Engineer has been useful for you.
Do share your perspective on the topic as a comment below and we are looking forward to hearing from you.